How to Remove and also Replace a Bath Tub.
How to Remove and also Replace a Bath Tub.
Blog Article
We have come across this post involving How to Install a Bathtub directly below on the internet and reckoned it made good sense to share it with you on this page.
Mounting a tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is easily obtainable, the job can relocate immediately; if you need to open up a wall to get rid of the old tub and also place the new tub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. See to it you have qualified on your own for the job as well as fit attempting it. Rather than working with a professional to take control of a halfway-completed task, it is far better to consider utilizing one before you start. Chances are you may require a professional plumber to make tube connections.
This short article will certainly aid you install a new bathtub in your shower room if you have actually currently acquired a new tub as well as do not need to change the arrangement of your previous water system pipes.
Your tools and also product list need to comprise the following:
Preparing for the Setup
First of all, the sustaining framework supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to stop stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be suited its final position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be quite bothersome due to the limited access that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the required setting. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bathtub up until the spirit level checks out level.
To install taps, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water system and inspect all joints as well as new pipework for leakages and also tighten them if required. Fill up the bathtub and additionally inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Lastly, deal with the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub should wait up until the bath tub has been utilized a minimum of when as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers are in place in between the faucet and the sink. Secure the faucet in place with the producer supplied backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former type must be connected to the faucet ends first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, creating the water to penetrate the wall between the bathroom and the tiling, leading to problems with dampness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack rather early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily offered on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about How to Install a Bathtub Yourself, I was thinking sharing that portion was worthwhile. Appreciated our entry? Please share it. Help others check it out. We recognize the value of reading our article about How to Install a Bathtub.
Schedule Appointment Report this page